It's important for the wheelchair to be fitted properly and be as narrow as possible while maintaining comfort and safety. This will insure the best performance for navigating tight areas both inside the home as well out in public spaces.

A wheelchair that is too narrow or too wide can cause discomfort. When too narrow, a wheelchair can become restrictive and increase the likelihood of pressure sores, while when it's too wide, becomes more difficult to push due to the angle of the arms from the shoulders to the wheels.

To determine the necessary seat width, measure the rider's widest area of the body and add one inch. This will allow for optimum seat width while maintaining ideal usability, comfort and safety.

To determine the appropriate seat height, measure from the bend of the knee to the bottom of the foot. Subtract the height of the seat cushion if one is being used. If the wheelchair is not being self propelled by the feet, also add about 2 inches to allow for foot clearance.

The rear of the seat is generally set at lower height than the front of the seat to prevent sliding forward.

Armrests are mostly a matter of personal choice, but most often users without much mobility appreciate armrests to help alleviate shoulder and back stress. Armrests also provide additional stability for users with limited upper body balance and are helpful when navigating in and out of the wheelchair. Additionally, armrests allow users the ability to do pushups, helping relieve pressure as well as protecting clothing from the wheels.

When armrests are not fitted properly the wheelchair can become more difficult to push. Not all armrests are adjustable. Height should be fitted to allow the forearm to rest fully on the armrest without pushing up on the shoulders. For users who sit at a table or desk, swing-away armrest can beneficial.

There are four basic types of armrests:
1. Full length, fixed height (entire armrest is padded with a non-adjustable height)

2. Full length, adjustable height (entire armrest is padded with various height seetings)

3. Desk length, fixed height (partial armrest is padded for easier access with tables, non-adjustable height)

4. Desk length, adjustable height (partial armrest is padded for easier access with tables, various height seetings)

Armrest that can be easily removed or flip up and down gives users the choice of when to use the armrests.

There are two types of rear wheels, Spoked Wheels and "molded" Mag Wheels.

1. Spoked Wheels are made of metal and are similar in appearance to that of bicycle wheels. The number and size of the spokes affect durability, shock absorption, weight, and performance. The more spokes, the more stable the wheel will be.

2. Mag Wheels are made of molded plastic or a composite. They have a small number of wide molded spokes that are an integral part of the wheel. Mag wheels are more durable, require less maintenance, and usually weigh more then spoked wheels.

There are typically three types of tires:

1. Pneumatic (air-filled) tires provide a softer ride, but need to be kept inflated. Because pneumatic tires are softer than urethane tires, they are harder to push, with more resistance to the shoulders.

2. Pneumatic Flat Free (foam-filled) tires provide a stiffer ride compared to air-filled tires, and will never go flat.

3. Urethane (solid, flat-free) tires provide the quickest and stiffest ride. And they will not go flat.

Tire Tread also affects the wheelchair ride. Tires with very little tread offer a quicker ride and turn more easily because there is less rubber in contact with the ground, causing less friction. "Knobby" tires with deep treads are helpful on unpaved and rougher surfaces, yet offer less maneuverability. A 1 3/8" treaded tire is a good basic tread for everyday use.

The greater the camber angle, the further the distance between the bottom of the rear wheels and the closer the distance between the top of the wheels. Increasing the camber angle provides the rider with increased maneuverability and stability, but also increases the overall width of the wheelchair.

Typically 0-3 degrees of camber is considered standard for everyday use to accommodate narrow doorways and aisles. A higher camber angle is useful for sporting activities such as basketball where added stability and maneuverability is desired.

There are various types of wheel locks available:

1. Push-to-lock wheel locks are the most common. The break is engaged by the rider pushing forward and applying pressure with the palm of their hand until the lever snaps into position.

2. Pull-to-lock wheel locks work in the same manner as the push-to-pock except the lever is pulled forward. For some riders, it may be easier because it does not require as much upper body mobility needed to push the lever away from the body.

3. Swing-away, low-mount and under-mount wheel locks work in different ways depending on the style. These wheel locks help you avoid hitting your thumbs when pushing directly on the tires by mounting the wheel locks away from this range of motion. Due to its location, some riders with limited mobility may not be able to engage these wheel locks.

Wheel lock extensions provide a greater lever arm to apply and remove the locking mechanism, making the wheel locks easier to engage for a rider with decreased upper strength.