TiLite 2GX Foldable Ultralight Wheelchair

A wheelchair that is too narrow or too wide can cause discomfort. When too narrow, a wheelchair can become restrictive and increase the likelihood of pressure sores, while when it's too wide, becomes more difficult to push due to the angle of the arms from the shoulders to the wheels.

To determine the necessary seat width, measure the rider's widest area of the body and add one inch. This will allow for optimum seat width while maintaining ideal usability, comfort and safety.

To determine the appropriate seat height, measure from the bend of the knee to the bottom of the foot. Subtract the height of the seat cushion if one is being used. If the wheelchair is not being self propelled by the feet, also add about 2 inches to allow for foot clearance.

A chair's rear seat-to-floor height is most commonly set at a height 1" lower than the front seat height.

The rear of the seat is generally set at lower height than the front of the seat to prevent sliding forward.

The greater the camber angle, the further the distance between the bottom of the rear wheels and the closer the distance between the top of the wheels. Increasing the camber angle provides the rider with increased maneuverability and stability, but also increases the overall width of the wheelchair.

Typically 0-3 degrees of camber is considered standard for everyday use to accommodate narrow doorways and aisles. A higher camber angle is useful for sporting activities such as basketball where added stability and maneuverability is desired.

1. Pneumatic (air-filled) tires provide a softer ride, but need to be kept inflated. Because pneumatic tires are softer than urethane tires, they are harder to push, with more resistance to the shoulders.

2. Pneumatic Flat Free (foam-filled) tires provide a stiffer ride compared to air-filled tires, and will never go flat.

3. Urethane (solid, flat-free) tires provide the quickest and stiffest ride. And they will not go flat.

Tire Tread also affects the wheelchair ride. Tires with very little tread offer a quicker ride and turn more easily because there is less rubber in contact with the ground, causing less friction. "Knobby" tires with deep treads are helpful on unpaved and rougher surfaces, yet offer less maneuverability. A 1 3/8" treaded tire is a good basic tread for everyday use.

Using wheel locks as a braking device can cause injury and excessive tire wear and should never be used in this manner.

There are various types of wheel locks available:

1. Push-to-lock wheel locks are the most common. The break is engaged by the rider pushing forward and applying pressure with the palm of their hand until the lever snaps into position.

2. Pull-to-lock wheel locks work in the same manner as the push-to-pock except the lever is pulled forward. For some riders, it may be easier because it does not require as much upper body mobility needed to push the lever away from the body.

3. Swing-away, low-mount and under-mount wheel locks work in different ways depending on the style. These wheel locks help you avoid hitting your thumbs when pushing directly on the tires by mounting the wheel locks away from this range of motion. Due to its location, some riders with limited mobility may not be able to engage these wheel locks.

Wheel lock extensions provide a greater lever arm to apply and remove the locking mechanism, making the wheel locks easier to engage for a rider with decreased upper strength.

When armrests are not fitted properly the wheelchair can become more difficult to push. Not all armrests are adjustable. Height should be fitted to allow the forearm to rest fully on the armrest without pushing up on the shoulders. For users who sit at a table or desk, swing-away armrest can beneficial.

There are four basic types of armrests:
1. Full length, fixed height (entire armrest is padded with a non-adjustable height)

2. Full length, adjustable height (entire armrest is padded with various height seetings)

3. Desk length, fixed height (partial armrest is padded for easier access with tables, non-adjustable height)

4. Desk length, adjustable height (partial armrest is padded for easier access with tables, various height seetings)

Armrest that can be easily removed or flip up and down gives users the choice of when to use the armrests.